行业新闻

机械设备的保养和维护是至关重要的环节
>> 返 回 <<
发布时间：2013/6/24
        聪明的资质、内在的干劲、勤奋的工作态度和坚忍不拔的精神，这些都是科学研究成功所需要的其他条件。
         Smart qualification, inner motivation, diligent working attitude and firm and indomitable spirit, which is the scientific research success other conditions required.
          行车配件的维修包括着两大内容:检查、维护与修理工作。这两方面的工作，有的属于司机职责范围，由司机负责进行，有的属于专业修理队伍或管理部门完成，司机应给予密切的配合。
         Vehicle accessories repair includes two contents: inspection, maintenance and repair work. These two aspects of the work, some belong to the scope of duties by the driver, the driver responsible for, some belong to the professional repair team or department of management, the driver should give close cooperation.
        对行车配件的检查与维护工作主要包括以下方面:司机交接班检查，定期检查(由司机和专业人员共同组成，有周检、月检、半年检等)及润滑等等。起重机的保养包括小修(零星修理)、中修和大修。小修一般是由有经验的司机担任、主要工作是预检、预修和排除临时性的故障。中修、大修由专门部门来完成。中修、大修的时间，决定塔机使用频繁程度，可由使用单位确定。
        The driving parts inspection and maintenance work mainly includes the following aspects: the driver handover inspection, regular inspection (component, jointly by the driver and professionals have the weekly inspection, monthly inspection, inspection, lubrication, and half a year). Crane maintenance including repair (sporadic repairs), repair and overhaul. Repair is usually by experienced drivers, the main work is as the fault detection, the AP and remove the temporary. Repair, overhaul completed by specialized departments. Repair, overhaul time, decided to tower crane use frequency, can be determined by using the unit.
        设备应进行日常维护，机械传动部分，连接部分，尤其是电气控制部分是日常维护工作的重点，进行的工作有:
Equipment should be carried out routine maintenance, mechanical transmission part, connecting part, especially the electrical control part is the daily maintenance of the focus of the work, the work:
         机械设备的保养：
        Machinery and equipment maintenance:
        ①制动电磁铁应经常进行检查和调整，制动瓦块与制动轮之间的间隙随制动器的不同类型和制动轮直径大小取不同值，对于块式制动器约调整在。.6^-1.75m二之间，具体数值查有关手册。在摩擦面上不应有污物(特别是油污)存在，.如遇有污物，必须用汽油洗净。
The braking electromagnet should always be checked and adjusted, and different types of brake wheel diameter size of the gap between the brake pad and the brake wheel with brake takes different values, for the block brake adjustment in about. .6^-1.75m two, the specific numerical investigation of the manual. In the friction surface should not have dirt (especially oil), if there is dirt, must wash with gasoline.
       ②对于转动部分和开式齿轮，要加足润滑油。对于有些开式齿轮，虽有防护罩但做不到全部密封，仍有外礴部分，因此仍要注意清洁，不使砂粒泥土等杂物进入齿轮，以防损坏。
For the rotating part and open gear, to add the lubricating oil. For some open gear, although the shield but do not sealed, there are still outside the new part, we still have to pay attention to clean, do not make the sand mud and other debris into the gear, in order to prevent damage.
         更多详情请咨询山东力王起重机械有限公司（http://www.ylqzjpj.com/），为您提供高端产品，周到服务！
        For more details, please consult the Shandong Longteng Hoisting Machinery Co., Ltd.  to provide high-end products for you, considerate service!
下一条： 起重机配件再使用时有哪些特殊要求     上一条： 根据不同的要求和情况选用合适的配件
热点新闻：
行车配件——车轮组对行车的作用 (阅读次数：2817 次)
行车配件之环链电动葫芦安装方法 (阅读次数：2607 次)
起重链条的焊接工艺及质量要求 (阅读次数：2557 次)
行车配件维修需要技巧，专业才是关键 (阅读次数：2527 次)
汽车起重机的吊臂伸缩形式简介 (阅读次数：2446 次)
行车配件是不是越贵越好呢？ (阅读次数：2417 次)
起重机配件双角钢滑轨悬挂装置介绍 (阅读次数：2402 次)
起重机配件齿轮常小故障解决的方法 (阅读次数：2381 次)
起重机安全问题——保证吊钩的防脱钩装置完好 (阅读次数：2309 次)
起重机采用油漆所考虑的因素 (阅读次数：2224 次)